陽極氧化的電壓一時間曲線大致可以分為三段
The voltage curve of anodization can be roughly divided into three sections.
靠前段：無孔層形成通電開始的幾至十幾秒時間內，電壓隨時間急劇上升至較大值，該值稱為臨界電壓(或形成電壓)。說明在陽極上形成了連續的、無孔的薄膜層(阻擋層)。此膜具有較高的電阻，因此隨著膜層的加厚，電阻加大，槽電壓急劇直線上升。無孔層的出現阻礙了膜層的繼續加厚，其厚度與形成電壓成正比，與氧化膜在電解液中的溶解速度成反比。在普通硫酸陽極氧化時，采用高頻氧化電源13～18V槽電壓，則無孔層厚度約為0.Ol～0.Ol5μm。該段的特點是氧化膜的生成速度遠大于溶解速度。臨界電壓受電解液溫度的影響很大，溫度高，電解液對膜層的溶解作用強，無孔層薄，臨界電壓較低。
The first section: the voltage rises sharply to the maximum with time, which is called the critical voltage (or the voltage) in a few to ten seconds of the starting of the electrified layer. A continuous, non porous film layer (barrier) is formed on the anode. The film has a higher resistance, so as the film thickens, the resistance increases, and the tank voltage rises sharply. The presence of a non porous layer hinders the continuous thickening of the film, which is directly proportional to the formation voltage and inversely proportional to the dissolution rate of the oxide film in the electrolyte. In normal sulfuric acid anodizing, the thickness of the non porous layer is about 0.Ol to 0.Ol5 0.Ol5 m when the frequency of the high frequency oxidation power supply is 13 ~ 18V. The characteristic of this section is that the formation rate of oxide film is much larger than that of dissolution. The critical voltage is greatly affected by the temperature of the electrolyte, the temperature is high, the electrolyte has strong dissolution effect on the film, the thin layer has no pore, and the critical voltage is low.
第二段：膜孔的出現陽極電位達到較高值以后，開始下降，其下降幅度為較大值的10%～15%。這是由于電解液對膜層的溶解作用，使氧化膜較薄的局部產生孔穴，電阻下降，電壓也隨之下降。氧化膜有了孔隙之后，電化學反應可繼續進行，氧化膜繼續生長。
The second paragraph: after the anodic potential reaches the highest value, the decrease of the membrane hole is 10% to 15% of the maximum value. This is due to the dissolution of the electrolyte on the film, resulting in holes in the thinnest part of the oxide film, and the resistance decreases, and the voltage drops. After the oxide film has pores, the electrochemical reaction can continue and the oxide film continues to grow.
第三段：多孔層的增厚此段的特征是氧化時間大約20s后，電壓開始趨于平穩。此時，阻擋層生成速度與溶解速度達到平衡，其厚度保持不變，但氧化反應并未停止，氧化膜的生成與溶解仍在每個孔穴的底部繼續進行，使孔穴底部向金屬內部移動，隨著時間的延長，孔穴加深形成孔隙和孔壁。由于孔隙內電解液的存在，導電離子便可在此暢通無阻，因此在多孔層的建立過程中，電阻值的變化并不大，電壓也就無明顯的變化，反映在特性曲線上是平穩段。多孔層的厚度取決于工藝條件，主要因素為溫度。在陽極氧化過程中，由于各種因素的影響，使溶液溫度不斷提高，對膜層的腐蝕作用也隨之加大，不僅孔底，也使孔口處膜層及外表面膜層的腐蝕速度加大，因此多孔層厚度增長變慢。當孔口膜層的腐蝕速度與孔底處的成膜速度相等時，多孔層的厚度就不會再繼續增加，該平衡到來的時間越長，則氧化膜越厚。
The third stage: thickening of the porous layer is characterized by a gradual stabilization of the voltage at about 20s. At this time, the formation velocity of the barrier layer is balanced with the dissolution rate, and its thickness remains unchanged, but the oxidation reaction does not stop. The formation and dissolution of the oxide film continue to be carried out at the bottom of each hole, making the bottom of the hole moving to the inside of the metal, and with the prolongation of time, the hole and the hole are formed to form pore and hole wall. Because of the existence of the electrolyte in the pores, the conductive ions can be unimpeded here, so the change of the resistance value is not significant during the establishment of the porous layer, and the voltage has no obvious change, which is reflected on the characteristic curve as a stationary phase. The thickness of porous layer depends on the technological conditions, and the main factor is temperature. In the process of anodic oxidation, the corrosion of the film is increased because of the influence of various factors, and the corrosion of the film is increased. The corrosion rate of the diaphragm and the surface film layer is increased by the hole bottom, so the thickness of the porous layer increases slowly. The thickness of the porous layer will not continue to increase when the corrosion rate of the pore layer is equal to the velocity of the film forming at the bottom of the hole. The longer the arrival time of the balance, the thicker the oxide film is.